Question by serendo.power: Can you machine a Alum Engine Block in a saab 1994 Saab 900 se Turbo?
It overheated when it ran out of water
Best answer:
Answer by Mr. KnowItAll
Sure……….
Know better? Leave your own answer in the comments!
Question by Michael Bolton: If I have an old 302 block that’s stripped, do I have to take it to a machine shop?
Can I just clean it myself? Do I have to get it bored if the walls of the cylinders are scuffed? If I get it bored, what should I bore it to?
Best answer:
Answer by Sam Korp
depends on how scuffed if you get it bored bore it to what ever the engine shop recommends its is going to depend from engine to engine.
Give your answer to this question below!
Question by carolina y: What parts and what machine work do I need to build a 10,000 rpm big block Chevrolet engine?
Best answer:
Answer by John S
how long do you need it to run ?
Know better? Leave your own answer in the comments!
Question by J. K: cost of Block and head machine work for Chevy 350 engine?
How much does it cost to have a 350 block hot tanked, bored, and have the heads machined? I just want a ball park price range for all machine work on block and heads.
Best answer:
Answer by dodge man
roughly around 600 bucks right now its around 15-20 bucks a hole to bore it,and by the time they mill the heads and the block a few thousands,and get it all trued back up it should be around 600 if they do a real good job on it,last one i had done was a 305,and i paid around 450 for it,and that was several years ago,and all shops will have different prices also ,beware of real low prices though ,good luck hope this helps.
Give your answer to this question below!
Question by D-Block: When I bring my d15b2 block to the machine shop what should I ask them to do?
I am going to be building for power so bore,hone,and decking I know but how much bore should I do and then what pistons should I get to match and then a head. This is going to be a mini-me.
Best answer:
Answer by L H
why even bother on a D15? Get an imported ZC or B18 and start with power right out of the box, less money than machining a D15 too. Check out www.hasport.com on their cross-fit applications for your model – what honda motor fits your chassis and how much work…
Add your own answer in the comments!
Question by Alexander K: how much does a machine shop charge to have a block bored out and honed?
like a .010 bore on a v8. im just looking for a ball park est. and i will call local shops if i decide to go ahead with the rebuild
yeah im going to replace cam, crank, connecting rods, pistons, lifters and prob have the heads reworked
Best answer:
Answer by Gary
Probably cheaper to buy a rebuilt engine, you never know what else might need replacing like cam or crankshaft. Just a suggestion
What do you think? Answer below!
Question by Roxanne N: How much in machine work does it usually cost to convert an lt1 (small block chevy) from 2 bolt mains to?
4 bolt mains?
Best answer:
Answer by bmwrider001
the blocks are different, so are the main caps, they can be steel or ductile iron, here is some straight dope on the subject:
http://www.jegs.com/p/Dart/Dart-SB-Chevy-Little-M-Engine-Block/748414/10002/-1
Know better? Leave your own answer in the comments!
Question by Chevy P: I have a small block 406 I want to build and I need a good machine shop.?
If you live in GA in the cities of Athens, Covington and Conyers or near them do you know any good machine shops that build and do good engine work, if so can you give me the shop names. I live in the city of Madison, Morgan county Georgia.
Best answer:
Answer by stush30@verizon.net
Check with any auto/truck repair shop (new car dealers included) and ask who they use when they can’t do their own machine repairs.
Know better? Leave your own answer in the comments!
